CPM offers quality used injection molding equipment, auxiliary lines of dryers, loaders, temperature controlers along with custom manufactured Screws and Barrels. Central Plastic Machinery
H2-Series Standard Features
Standard Features | Optional Features
• TM-110 H2
• TM-150 H2
• TM-200 H2
• TM-245 H2
• TM-300 H2
• TM-400 H2
• TM-500 H2
Download PDF File
[PDF File]
Need a Brochure?
View Brochure Directory
View Brochure Directory
  Email this Page Print this Page
« Injection  
  • Multi-step injection control
  • Multi-step metering control
  • Holding pressure changeover via position, time and pressure
  • Injection slope control
  • Suckback (before and after metering)
  • No back pressure metering in manual mode
  • Injection unit swiveling device (with nozzle alignment mechanism)
  • Melt run-out detection system
  • Programmable melt purging system
  • Purge cover (with an interlock)
  • Sprue break
  • PID temperature control for hopper throat
  • SSR control for heaters
  • Heater temperature holding control
  • 5-zone heater control
  • Hopper (with a shutter)
  • Hopper swiveling device
« Clamping  
  • Multi-step mold opening control (2-5 steps)
  • Multi-step mold opening control (3-5 steps)
  • Mold exchanging mode (low pressure and speed)
  • Automatic clamping force setup system
  • Low pressure mold protection system
  • Mold protection in mold opening and ejecting
  • Double-roller-supported movable die plate
  • Triple safety device (electric, mechanical, hydraulic
  • Emergency stop push button (front and rear)
  • Multi-step ejector advance control (1-3 steps pressure control)
  • T-throtted die plate (300H2 to 500H2)
  • Mold height extension (245H2 and up :3.93 in)
  • Mechanical stopper for mold opening (not available for 350H2 and 450H2)
« Hydraulic  
  • Automatic hydraulic temperature control system
  • Hydraulic oil heat-up system
  • Hydraulic oil cooling circuit
  • Y-type strainer for cooling water circuit
  • Oil cleaner
  • Oil cleaner clogging alarm
  • Oil temperature alarm
  • Oil level alarm
« Control  
  • PLCS-11 control system (TFT color LCD, full touch panel)
  • Digital setting for all the machine parameters
  • Internal memory for 32 mold setups
  • Graphic display of injection and metering motion
  • Monitor graph indication
  • Statistical processing of monitored data (SPC)
  • Manned-unmanned operation selection
  • Hour meter
  • Counters (cycle, lot, initial purge, etc.)
  • Monitoring function (32 items selected from 83 items including positions, speeds, pressures, times, and revolutions)
  • Alarm function (cycle time, up-down tolerance, heater disconnection, thermocouple disconnection, safety door, etc.)
  • Machine status indication (operation mode, mold clamping completion, ejector-retraction completion)
  • Production control function (Job completion ratio, prospective time of job completion, etc.)
  • Maintenance function (one cycle graph, alarm-history)
  • Self diagnosing function
  • Screw-diagnosing function
  • Screw cold-start prevention system
  • Fine PID temperature control (with slope ramp up)
  • PID auto-tuning function
  • One week automatic heater on-off calendar
  • RS-232C interface (1 pc.)
  • Printer terminal
  • 100V plug socket for printer (1pc.)
  • Parameter setting history
« Other  
  • Cooling water piping for mold
  • Memory card for 128 mold setups
  • Interface for robot
  • installation pads
  • Screw disassembling tool
  • Standard accessories (tool, spare grease, hand grease pump, spare filter element)
  • Mold fittings